Two dark grey 3D-printed replacement brackets on a wooden tableParts
A red and white 3D-printed electronics case with slotted vents on a deskCases
A lit 3D-printed arch lamp showing a photo of a dogGifts

Broke a part? Get it reprinted.

Discontinued, obsolete, or just impossible to find? Describe the part or upload a 3D file, and verified makers will quote to make a replacement from your photos or sketch. We hold your payment until it is delivered.

Prices start as low as $15.

Start with an example

3D file?

A few words or a photo is enough.

  • Verified makers
  • Payment held until delivery
  • No setup fee

How it works: tell us what you need, makers send quotes, you pick one. We hold your payment until it is delivered.

Try: 6mm spacer · 1/4 inch shelf pin · washer dial knob · or send a photo and makers will quote to make it

How to show us the part

  1. A photo from above, with a ruler or a coin next to it.
  2. A photo from the side.
  3. Where it fits: the hole, the slot or the post it goes on.
  4. The brand and model, if they are printed on it.

Made by makers here

Two dark grey 3D-printed replacement brackets on a wooden tableA replacement part
A lit 3D-printed arch lamp showing a photo of a dogA photo lamp
A red and white 3D-printed electronics case with slotted vents on a deskAn electronics case
A 3D-printed wall panel of a tree in flames, in orange and yellow on blackA multi-color panel
A tall white 3D-printed flame sculpture on a deskA sculpture
A white 3D-printed figurine of a robed man holding stone tabletsA figurine

What we'll ask next

  1. Already answered

    What you told us here

    Your words or your photo (or your 3D file). It comes with you, so you never type it twice.

  2. You add this

    Up to three quick questions

    About your item, like how it attaches. Tap an answer, add a photo, or skip: makers can ask you later.

  3. You add this

    Where it goes

    A ZIP code is enough to get quotes. The last thing before makers send them.

Send it and verified makers reply with quotes. Most requests get a first quote the same day. You pay nothing until you accept one.

Questions

I don't have a 3D file — can you still make the part?

Yes. Send clear photos (a ruler in frame helps), a sketch with measurements, or the dimensions you know, and a maker can model the replacement before printing it. The first thing you get back is a quote, so there is no commitment to find out.

What kinds of replacement parts can be printed?

Common ones include knobs, dials, clips, brackets, gears, housings, hinges, and appliance, furniture, or equipment parts that are no longer sold. If it is small-to-medium and not under heavy structural load, it is usually a good candidate — a maker will tell you when they quote.

Which material should a replacement part use?

It depends on the job. PETG and ABS handle heat and stress better than PLA; nylon and TPU add toughness or flex. Describe how the part is used and makers will recommend a material when they quote.

How much does 3D printing cost?

Up to mug size: $15–$32 to start. One part is fine. Upload your model and you get a starting price range right away, no account needed. Verified makers then each send a quote for your part, so the final price comes from a maker, not a guess. You pay at checkout when you accept one, and we hold the money until your print is delivered.

What file formats can I upload?

STL, OBJ, 3MF or STEP, up to 100 MB each. Drop your model in and we measure it to show its size and a starting price. No file? Add a photo or describe the part instead.

Do I need an account to get quotes?

No. You can upload a file for a starting price, or describe the part and get an answer, without signing up. You only create an account when you are ready to get quotes from makers and place an order.

Is there a minimum order?

No. One part is fine. Every job has a $15 minimum, so even a tiny part is quoted at $15 or more. No setup fees.

When do I pay, and is it safe?

You pay at checkout when you accept a quote, and we hold the money until your print is delivered. The maker is paid only after that.

What materials can I print in?

Common options include PLA, PETG, ABS, resin, nylon and TPU. Makers list the materials they support, and you can choose the right one for strength, detail or flexibility.